Abus FU8007 Secvest 2WAY Base Kit Operating instruction Manuale Utente

1 Secvest 2Way O P E R A T I N G I N S T R U C T I O N S BOM-No 12000869

10 8.3. Delay time started The alarm system starts the delay time, but with a pulsed tone instead of a continuous tone. This indicates that one or

119. Following successful activation When the alarm centre is successfully activated (also with automatically omitted zones), an acknowledgement is

1210. Deactivating the wireless alarm system The wireless alarm system can be deactivated in a variety of ways: • Deactivation of the entire system

1311. Activating partitions If the alarm system is set up so that two or more partitions can be monitored independently of each other, these partiti

14 12. Internal activation In addition to monitoring one or more partitions (i.e. objects or company departments) separately, the system also has an

1513. Alarms The wireless alarm system has three different types of alarm. Depending on the system state (deactivated, internally activated, activa

1614. Resetting the alarm If the alarm system has triggered an alarm (whether local, external or silent), then this must first be acknowledged and

1715. Alarm transmission by telephone In addition to alarms from sirens and signalling devices, the wireless alarm system can also transmit an alar

18The alarm centre registers the status of your commands through different tones: Beep = Command accepted Beep, beep = Action carried out Bup = A

1918. Settings in the user menu 18.1. First steps in the user menu In the user mode, proceed as follows: Press the control button under Menu. E

2 Preface Dear customers, Many thanks for your purchase of the SECVEST 2Way wireless alarm centre. This device is built according to state-of-the-

2018.3. Recording voice messages The wireless alarm centre enables the user to record individual voice messages. These voice messages can be listen

2118.4. Omitting zones If necessary, you can remove zones from surveillance (e.g. if a detector is defective or a zone cannot be closed).

2218.5.1. Editing users After selecting the Edit User menu item, the user attributes can be edited. Select the user whose attributes

2318.5.1.2. Changing the user type Select the user type: • Normal User • Administrator In contrast to the normal user, the administra

2418.5.1.4. Changing the user code Select the Code menu item. Enter the new four-digit code via the keypad. After entering the last digi

25Training the chip key Select Tag. The system prompts you to hold the chip key over the system reader. Hold the chip key over the alarm s

2615.5.2. Adding users To add a new user to the wireless alarm system, select the Add User menu item. You are now guided through the rema

2718.6. Viewing the log This function enables you to read the event log. This log contains the last 250 events together with the date and time. The

28System Rearmed The system has automatically reactivated itself following an alarm. U-- Z== Omit User -- has omitted zone ==. Fire Z== Alarm Zon

29 18.7. Additional functions In this menu, a user can switch the functions assigned to them by the installer on and off. Select the Faci

3 2. Contents Preface ... 2 Introduction ..

3018.8. Test This menu is used to test the different alarm centre functions. Select the “Test” menu item. Select the function

31Outputs A list of all outputs installed on the system is shown on the display. Select the output to be tested. Press Done to end the test. IMPORT

32 Function Meaning Set Date & Time Select this point to enter the date and time of the wireless alarm system. Edit Outputs Select this poi

3318.9.1. Week Planner Only users with administration rights can install this function. The system should be activated and deactivated according t

3418.9.2. Activation / deactivation of the week planner Access the user menu using the administrator code (default = 1234) and create a week planne

3518.9.4. Auto Set Select the time for Auto Set (00:00). Æ Select data record 1. Æ Select activated

3618.9.5. Auto Unset Select the time for the Auto Unset (07:20). A data record has now been programmed for Mon

37 18.9.6. Internal and external activation In this example, partition 1 is switched from internal activation (external perimeter protection) to ex

3818.9.6. Activating and deactivating data records To deactivate a data record (time period), make changes in the AUTO SET menu. In AUTO UNSET, cha

3918.10. Follow Me This menu is used for entering the follow me number. This number is dialled to send a voice message to a telephone of your choic

4 3. Safety information !WARNING! To avoid fire and injury, please note the following: • Securely fasten the device in a dry location

4018.12. Telephone Call This menu is used to start a telephone call manually and test the telephone line or GSM connection. The system uses the int

4119.1. Errors, meanings, causes and suggested solutions Displayed error Meaning Possible causes Suggested solutions AC Fail The 230 V AC syste

42Displayed error Meaning Possible causes Suggested solutions Low Batt Z__ No battery power supply in zone __. • The battery capacity in the de

43 20. Declaration of conformity The declaration of conformity to the applicable guidelines has been made available and signed by Security Center m

44

A1 - I Amendments to the operating manual (UK) Secvest 2WAY FU8006 S/W ≥ 5.04.22

A1 - II 1. Preface Dear customers, We constantly develop our product range in order to provide our customers with optimal products incorporating s

A1 - III 3. New menu items in user menu 3.1. Secvest Key 2WAY wireless cylinder, item no. FU59xx • Testing User Menu Æ Testing Æ Secvest Key S

A1 - IV 3.2. FU8100 wireless remote control User Menu Æ System Config Æ Telecommands Æ 2 Way Instant Set Æ 2 Way Instant Set Y 2 Way Instant Set

5 4. System and keypad overview 1 – Chip key reader 2 – Graphic display Multiple-line display 3 – Integrated siren 4 – A

6 5. Graphic display The graphic display informs you about all events concerning the wireless alarm system. The following is an overview of the diff

7 6. Activating the wireless alarm system The wireless alarm system can be activated in a variety of ways. The system emits an acoustic message. De

8 7. During the delay time Provided no errors that prevent activation have occurred (zone open), the wireless alarm system starts the configured exi

9 Using the control button, select the item under View to display the error. The following graphic display is shown: The wireless alarm s